Free Car Diagnostic Check
Enter the Free Car Diagnostic Check. This comprehensive guide is your roadmap to understanding how you can perform a free car diagnostic check at home, empowering you to keep your car running smoothly without breaking the bank.
Technical Statistic Premium Car Repair
Looking for reliable and efficient car repair services? Our skilled technicians are here to assist you with any car issues
9+
Years
Experience
186
Project
per Week
80.000+
JOB
98%
Satisfied
Customer
Why is a Car Diagnostic Check So Important?
List of faults and car modules we can definitely fix for you
| MERCEDES | SCN Offline Camera 360 | – Programming and Coding New 360 Camera Control Box after Replacement |
| MERCEDES | SCN offline VGS 1,2,3 control module | – Programming and coding of the new transmission control module after replacement. |
| MERCEDES | Reset AdBlue | – After the AdBlue system maintenance and refilling with AdBlue fluid, the replacement days need to be reset to calculate the next maintenance cycle. |
| MERCEDES | Anti-theft protection activated radio | – After replacing the ECM engine control module or headunit, a warning will appear regarding the anti-theft protection of the radio control unit, requiring a pin code to unlock it. |
| MERCEDES | SCN offline Headlight | – After replacing the front headlight control module, programming and coding need to be done to set up the new control module. |
| MERCEDES | SCN offline ESP (ABS) electronic stability program | – After replacing the electronic stability control module (ESP), programming and coding need to be done to set up the new control module. |
| MERCEDES | SCN offline EPS (Electronic Power Steering) | – After replacing the electronic power steering (EPS) module, adaptation and coding need to be done to set up the new control module. |
| MERCEDES | Support calibration of the camera with special tool | – Support for recalibrating the camera angle after replacing the camera (not the camera control module). |
| MERCEDES | Disable/Activate hood warning | – Error warning for the hood not being closed on vehicles without a sensor or without this feature enabled, which still shows up on the dashboard display, needs to be coded off. |
| MERCEDES | SCN offline ORC (Airbag) | – After replacing the airbag control module, programming and coding need to be done to set up the new control module. |
| MERCEDES | Turn off and on start/stop for all cars | – This is a feature to enable or disable automatic start and stop while the car is idling at traffic lights. |
| MERCEDES | Change sound volume for Benz door opening & closing | – Change the sound volume for car door opening and closing. |
| MERCEDES | Activate Daylight for Mercedes-Benz | – Enable the daytime running lights to stay on when it is still daylight. |
| MERCEDES | SCN offline front SAM and rear SAM control module | – After replacing the fuse and relay control module, programming and coding need to be done to set up the new control module. |
| MERCEDES | Coding key warning if leaving car | – Enable or disable the key warning when the key is not in the car. |
| MERCEDES | Activate Benz ECU Fahrdynamik/Drive Dynamic | – Enable automatic damping adjustment based on driving mode and road conditions. |
| MERCEDES | Coding LED lights turn on with daylight activated | – Enable LED lights to turn on with daytime running lights. |
| MERCEDES | Coding activate remaining fuel liters | – Enable the display of remaining fuel on the instrument cluster. |
| MERCEDES | Coding DVD region changing | – Change DVD region code. |
| MERCEDES | Coding speed limit signs display (Map & MPC/Camera Data) | – Enable speed limit sign warnings to display from the camera to the instrument cluster. |
| MERCEDES | Coding CD ripping mode – Copy music audio CDs to internal HDD | – CD ripping mode – Copy music audio CDs to the internal hard drive. |
| MERCEDES | Coding turn signal flasher changed from 3x to 5x | – Change turn signal flashing from 3 flashes to 5 flashes on the instrument cluster. |
| MERCEDES | Coding turn on sidemarker when turn signal is on | – Enable turn signal side marker lights. |
| MERCEDES | Coding for Benz ventilation bar display turned on auto mode | – Disable the Mercedes-Benz ventilation bar display in auto mode. |
| MERCEDES | Coding temperature offset to set air conditioning colder | – Temperature offset feature for adjusting the internal vehicle temperature. |
| MERCEDES | Coding for Benz pedal characteristic curve – Faster engine response | – Modify throttle pedal response to improve engine response. |
| MERCEDES | Coding hill assist start function | – Enable hill assist start function. |
| MERCEDES | Coding for Benz brake hold function | – Enable brake hold function, allowing the car to remain stopped at traffic lights without using the brake pedal. |
| MERCEDES | Coding for Benz ME97 ECU changing Vmax | – Increase vehicle speed limit to 250 km/h. |
| MERCEDES | Coding tire pressure control system deactivation | – Disable tire pressure monitoring system. |
| MERCEDES | Coding deactivate seat belt warning | – Disable seat belt warning sounds during driving. |
| MERCEDES | Turn on/off Benz daytime running light menu | – Enable or disable the manual control of daytime running lights from the dashboard. |
| MERCEDES | Change language for COMAND | – Change the language on the headunit screen. |
| MERCEDES | Display/Switches brightness menu activation | IC204 | – Enable brightness adjustment for the instrument cluster using a control knob. |
| MERCEDES | Delete AdBlue system, turn off DPF | – Permanently disable the smart exhaust gas treatment technology system due to frequent errors caused by incorrect sensor readings, which limits the vehicle’s speed and increases repair costs. |
| MERCEDES | Map data does not match COMMAND, please insert the map data DVD with the correct map material | – Fix data display issue on HU45 Mercedes 204, update map data by region. |
| MERCEDES | Fix error: Collision Prevention Assist Plus Inoperative W205 | – Fix the Collision Prevention Assist Plus error on Mercedes models (system inoperative). |
| MERCEDES | Control unit “Trunk lid/tailgate control” has a malfunction. The signal calculation is faulty | – Error in the trunk control module, which causes issues with the trunk lid or prevents proper trunk operation. |
| MERCEDES | The remaining distance is limited due to a malfunction in the AdBlue system | – Error indicating limited distance due to a malfunction in the AdBlue system. |
| MERCEDES | The internal data could not be stored in the control unit | – Issue starting the vehicle with the Autel update device, code issue due to missing data in the control module. |
| MERCEDES | Intelligent light system not functioning | – Error warning on the dashboard when replacing the right headlight control module. |
| MERCEDES | Coding remove airbag light error (Drive authorization data implausible. There is an implausible signal) | – Airbag control module replacement error. |
| MERCEDES | Enable ENGINEDATA feature on the head unit | – Enable data for vehicle operational status. |
| MERCEDES | Enable traffic sign assist feature | – A feature to display speed limit signs on the screen. |
| MERCEDES | Disable collision prevention assist warning | – A feature that detects nearby traffic obstacles and provides audio and visual alerts, which can be disabled. |
| MERCEDES | Fix mileage after cluster change | – Correct the mileage reading on the vehicle after replacing the instrument cluster. |
| MERCEDES | Remove brake pad wear warning | – Brake pad maintenance warning. |
| MERCEDES | Change timezone on HU6 | – Replace the headunit control module, which had an incorrect timezone setting (from a used vehicle). |
| MERCEDES | Airbag warning light | – Airbag warning light flashing continuously without any actual issue. |
| VAG | Antitheft audio, radio audi | – Error message after changing radio box need to unlock if control box is used |
| VAG | Sound system, component protection | – fix error after replacing radio part |
| VAG | Comfort module Component protection active audi | – replace body box on car |
| VAG | Error code 02095: Component protection active on Instrument cluster appears after module replacement | – Error in software 02095 |
| VAG | – On the IC screen displays the warning “SAFE” | |
| VAG | – All vehicle error warnings will appear on the Instrument cluster | |
| VAG | Instructions for troubleshooting error U110100 Component protection active on ABS module after replacement | – ABS error warning light appears on Dashboard and error U110100 Component protection active appears in diagnostic software. |
| VAG | SVM Level Control System | – After replacing the Level control system (J197) control box, the accompanying software, coding data and as-built data do not match the vehicle. Parameterization is required to standardize the data |
| VAG | Calibration Level Control System | – After replacing the Level control system (J197) and performing parameterization, it is necessary to perform Calibration to calibrate the system. |
| VAG | 18055 P1647 ABS checking coding/versions of in powertrain | – Error occurred when replacing airbag |
| VAG | B200049 | – Steering wheel programming when having trouble shifting gears |
| VAG | Programming add/remove dealer key | – programming add/remove certain number of genuine keys. Maximum 8 keys |
| VAG | Unlock engine box after replacement | – ECM locked error message after replacing the engine box ECM needs to synchronize immo with the key. The car cannot start or the engine starts and turns off immediately. |
| VAG | Programming and coding the motor box after replacement | – After replacing the motor box with inappropriate software, it is necessary to update the software and recode. |
| VAG | Coding disable the DRL (daylight running time) system | – After turning the key to the ON position, the Daytime running lights automatically turn on and cannot be turned off, which weakens the battery. |
| LANDROVER | Programming RLM suspension system after replacing the lift control box Error U1A35-62 | – RLM module is faulty or replace with new module (RLM) need programming to operate normally. Error appears on Dashboard Suspension Fault and max speed can go 50 Km/h |
| LANDROVER | Disable TPMS system when Tyre Pressure System Fault appears on dashboard Error C1A58-93 C1A59-13 | – When there is a failure or loss of connection with the tire pressure sensor or a problem with the sensor system, an error will appear. To save on repair or replacement costs, the car owner will choose to turn off the system. Or more simply, the TPMS system sometimes sends false warnings about tire pressure, causing unnecessary trouble for the car owner. |
| BMW | Tailgate and Lift System | – CODING TAILGATE Series X 2017 BMW |
| BMW | – Replace Tailgate Control Box | |
| BMW | – Tailgate Lift Box | |
| BMW | Exterior Lighting Systems | – Coding Disable Foglight BMW F22 |
| BMW | – Disable Fog Light for Cars with Fog Light Error | |
| BMW | – Coding Error Daytime Lights Fault BMW F25 | |
| BMW | – Code to Remove Cornering Lights | |
| BMW | – Xeon Lamp Update | |
| BMW | – Turn Off the Fog Light System | |
| BMW | Steering & EPS (Electric Power Steering) Systems | – Programming EPS |
| BMW | – Replace Steering Rack Error 4823CB: No Current Coding Data Stored | |
| BMW | – 4823CC Control Unit Not Coded for Vehicle, Vehicle Difficult to Steer | |
| BMW | – Replacing EPS Requires Programming and Coding | |
| BMW | – EPS Steering System Replacement | |
| BMW | ECU & Control Unit Programming | – Replace ECU Programming Error |
| BMW | – Reprogramming DME | |
| BMW | – Fix Missing Code Error | |
| BMW | – Add CAFD Code for EPS Box | |
| BMW | BCM (Body Control Module) and ICM (Instrument Cluster Module) | – BCM Fuse Box Fault Repair |
| BMW | – Coding Replaces ICM and DSC (Dynamic Stability Control) | |
| BMW | Airbag & Safety Systems | – Airbag Error Repair Code |
| BMW | – F20 Model Seat Airbag Warning Off | |
| BMW | – Calibration of Driver Seat Adjustment | |
| BMW | – Disable Pedestrian Protection System for Vehicles with Broken Sensors | |
| BMW | Key & Immobilizer Systems | – Customer Has EWS Key Error, Car Cannot Start |
| BMW | Infotainment & Connectivity Systems | – Active CarPlay |
| BMW | – Update Map | |
| BMW | – Coding Update I-Level | |
| BMW | – KAFAS Alternative Coding | |
| BMW | HVAC and Roof Systems | – Replace Sunroof Control Box FZD Used Coding and Programming Error |
| BMW | Transmission & Gearbox Systems | – VTG Sub-Gearbox Replacement Requires Coding |
| BMW | Disable Tow Hitch | – |
| BMW | Disable SOS Function | – |
| FORD | PATS function programming add/remove keys | – PATS function programming to add/remove keys |
| FORD | – IDS uses PATS functions to add dealer key | |
| FORD | – Programming new key at the dealership | |
| FORD | – Programming additional key for 2023 vehicle | |
| FORD | – Programming to add/remove a certain number of genuine keys (Maximum 8 keys) | |
| FORD | ABS (Anti-lock Braking System) Module Issues | – Replace ABS module used error programming and calibration |
| FORD | – Replace ABS module programming error with error code U2100-00 | |
| FORD | BCM (Body Control Module) & Immobilizer Issues | – Replace BCM error, car cannot start, check BCM programming |
| FORD | – Replace ECM immobilizer fault, car cannot start | |
| FORD | – Replace PCM module programming and immobilizer error | |
| FORD | – Replace PCM immobilizer error and programming | |
| FORD | ECM (Engine Control Module) & PCM (Powertrain Control Module) Programming | – Transit 2006, replace ECM box, need online removal of immobilizer |
| FORD | – Replace ECM immobilizer fault, car cannot start | |
| FORD | – Programming after airbag replacement | |
| MAZDA | Fuel Pump Control Module | – Coding error after replacing fuel pump control module |
| MAZDA | EIS (Electronic Ignition Switch) Drive Authorization Errors | – EIS error – VGS drive authorization |
| MAZDA | Night View Assist | – Calibration errors |
| MAZDA | Powertrain | – P044C11 error after EGR tuning off |
| MAZDA | Sunroof System | – Sunroof not programmed |
| MAZDA | SCM (Steering Column Module) | – Internal fault in steering angle sensor |
| MAZDA | SCR Module | – Reprogramming in boot mode |
| MAZDA | ABA (Active Brake Assist) | – Disable ABA function and IC warning |
| MAZDA | Collision Module | – Turn off collision function after module removal |
| MAZDA | FCVT (Fully Continuously Variable Transmission) | – Coding error when cloning data from original FCVT |
| MAZDA | ABS Module | – Coding ABS |
| MAZDA | – Replace ABS module (error coding incorrect and calibration) | |
| MAZDA | SOS Module | – Disable SOS function in gateway and IC |
| MAZDA | – Disable SOS function in gateway and HU | |
| MAZDA | Pre-Safe System | – Remove Pre-Safe warning after front radar removal |
| MAZDA | – Turn off Pre-Safe function (IC) | |
| MAZDA | – Replace seatbelt with Pre-Safe error on IC | |
| MAZDA | Lane Keeping Assist | – Turn off Lane Keeping Assist function |
| MAZDA | – Retrofit Traffic Sign Assist and Lane Keeping Assist | |
| MAZDA | Mirror System | – Enable turn signal function after mirror replacement |
| MAZDA | – Retrofit folding mirror, enable option in gateway | |
| MAZDA | Vehicle Specific Issues | – Incorrect VIN Issues (SRS, headlamp, and other modules). |
| MAZDA | – ECM and Immobilizer Replacement (adaptation and programming). | |
| MAZDA | – Camera and Parking Sensor Coding (e.g., 360 camera, RVC, parking sensors). | |
| MAZDA | Gateway Module | – Replace gateway with wrong part number (programming/coding) |
| MAZDA | – Coding Gateway Pre-Safe limit function | |
| MAZDA | – RHD to LHD coding and telecommunications | |
| MAZDA | Trailer System | – Retrofit trailer hitch and trailer lamp |
| MAZDA | – Retrofit trailer hitch | |
| MAZDA | Distronic System | – Disable Distronic function |
| MAZDA | – Turn off Distronic option after module removal | |
| MAZDA | Headlamp and Lighting Control | – Replace headlamp/control module (various coding errors) |
| MAZDA | – US to EU headlamp coding | |
| MAZDA | – PXL not configured error | |
| MAZDA | – DRL not working | |
| MAZDA | – Adaptive headlight errors | |
| MAZDA | Trunk/Boot System | – Incorrect VIN after trunklid replacement |
| MAZDA | – Pneumatic spring/tailgate shock absorber issues | |
| MAZDA | – Trunklid module not configured | |
| MAZDA | Radio/Infotainment System (HU) | – Radio anti-theft coding issues |
| MAZDA | – CarPlay activation | |
| MAZDA | – Software updates (bootloader, maps) | |
| MAZDA | – Frequency/language region change | |
| MAZDA | – MOST network issues | |
| MAZDA | – RVC (rearview camera) not working | |
| MAZDA | Immobilizer/Startkit | – Anti-theft issues after startkit replacement |
| MAZDA | – PIN-related radio errors | |
| MAZDA | Instrument Cluster (IC) | – Mileage correction after IC replacement |
| MAZDA | – SRS warning light issues | |
| MAZDA | – Change display language/color | |
| MAZDA | – Enable AMG menu | |
| MAZDA | – Enable turbo pressure/oil temp | |
| MAZDA | ISM (Intelligent Servo Module) | – Programming/adaptation errors |
| MAZDA | – Gear shifting issues (W164) | |
| MAZDA | Radar/Sensor Systems | – Coding errors after radar sensor replacement |
| MAZDA | – Rain/light sensor malfunctions | |
| MAZDA | – Roll control module coding errors | |
| MAZDA | SAM (Signal Acquisition Module) | – Programming/coding errors (various versions) |
| MAZDA | – Disable daytime running light (Citan) | |
| MAZDA | – Clone SAM from old unit | |
| MAZDA | SRS (Supplemental Restraint System) | – VIN-related errors |
| MAZDA | – Not locked errors | |
| MAZDA | – Weight sensing system issues | |
| MAZDA | – Coding errors after module replacement | |
| MAZDA | TPMS (Tire Pressure Monitoring System) | – Disable TPMS after module removal |
| MAZDA | – Coding pressure value errors | |
| MAZDA | VGS (Transmission Control Module) Coding & Adaptation Issues | – VGS variant coding/adaptation issues |
| MAZDA | – VGS coding data from old VGS | |
| MAZDA | – VGS coding | |
| MAZDA | – VGS coding data from VGS cũ (old VGS) | |
| MAZDA | – VGS coding with data from text | |
| MAZDA | – VGS3 coding – old VGS cannot connect | |
| MAZDA | – Coding VGS after DCT replacement (W117) | |
| MAZDA | VGS Virgin Coding & Data Cloning | – VGS virgin coding for used modules |
| MAZDA | – Data cloning from old VGS | |
| MAZDA | – VGS3 used requires virgin state and coding | |
| MAZDA | – VGS3 clone from old VGS | |
| MAZDA | – VGS3 0009 new cloned from VGS3 0034 | |
| MAZDA | – VGS3 hardware 0009 coding data from VGS3 0034 | |
| MAZDA | – VGS2 used requires virgin state and coding | |
| MAZDA | – VGS2 clone from old VGS2 | |
| MAZDA | – VGS1 used with old VGS2 | |
| MAZDA | – VGS1 to VGS2 coding | |
| MAZDA | – Customer software update (Autel) error – requires VGS3 reprogramming and coding | |
| MAZDA | VGS Drive Authorization Issues | – VGS FDCT drive authorization error after battery replacement |
| MAZDA | – EIS error – VGS drive authorization | |
| MAZDA | – Adapt drive authorization | |
| MAZDA | VGS Hardware & Connectivity Issues | – VGS3 (old PCB) cannot connect |
| MAZDA | – VGS3 new (old PCB) cannot connect | |
| MAZDA | – VGS3 coding – old VGS cannot connect (attempt 2) | |
| MAZDA | – VGS3 hardware replacement (0009) – coding from VGS3 0034 | |
| MAZDA | – VGS3 new cloned from original VGS3 | |
| MAZDA | – VGS2 downgrade from VGS3 original | |
| MAZDA | – VGS2 coding – old VGS data lost | |
| MAZDA | VGS ISM (Intelligent Servo Module) Coding & Communication Errors | – ISM and VGS3 (new generation 0009) – car cannot shift gears |
| MAZDA | – VGS, ISM not recognizing RND positions | |
| MAZDA | EGS (Electronic Gear Selector) Coding & Programming | – EGS53 module coding error – car cannot shift gears |
| MAZDA | – EGS coding data from text | |
| MAZDA | – Coding EGS53 cloned from old PCB | |
| MAZDA | Activation Features (AMG/Driving Modes) | – Activate AMG IC, A mode, M mode for VGS4 |
| MAZDA | – Activate A mode, M mode for EGS52 | |
| MAZDA | ECU Replacement & Programming Errors | – Replacing used ECU with programming and coding errors |
| MAZDA | – Replacing new ECU (MED177) without programming; old ECU cannot connect | |
| MAZDA | – Replacing ECU with incorrect VIN, coding, and drive authorization errors | |
| MAZDA | – Replacing ECM with coding and authorization errors | |
| MAZDA | – Replacing ECM with coding errors | |
| MAZDA | – Replacing ESP module with missing coding | |
| MAZDA | – Replacing EPS module with missing ESP coding | |
| MAZDA | ECU Fault Codes & Starting System Issues | – ECU Fault Codes |
| MAZDA | – ECU Error P031500: Sensor rotor adaptation not performed | |
| MAZDA | – ECU variant coding error after converting from automatic to manual transmission | |
| MAZDA | – Checking ECU not starting after cloning | |
| MAZDA | – Used ECU SIM271DE20 with coding error, engine won’t start | |
| MAZDA | – Sprinter W906 ECU check, unable to start | |
| MAZDA | – ECU speed limit removal (Vmax) for Sprinter 906 | |
| MAZDA | ECU Drive Authorization & Non-Starting Issues | – Fixing vehicle not starting due to drive authorization errors |
| MAZDA | – Support for non-starting issues related to drive authorization | |
| MAZDA | – Check ECU (car cannot start) | |
| MAZDA | Power Steering & EPS Module Replacement and Programming | – Programming power steering |
| MAZDA | – Replacing power steering (same hardware) with variant coding errors | |
| MAZDA | – Replacing power steering (different hardware) with variant coding errors | |
| MAZDA | – Replacing EPS module with coding errors | |
| MAZDA | – Replacing EPS with same part number, variant coding error | |
| MAZDA | – Replacing steering rack with the same part number, requiring coding reset | |
| MAZDA | – Replacing steering rack with the same part number | |
| MAZDA | EPS System Faults | – Programming power steering with P063500 error: Electric power steering malfunction |
| MAZDA | – Replace power steering control box settings for Mazda3 | |
| MAZDA | – Replacing EPS module with incorrect coding | |
| MAZDA | – Replacing EPS module with missing ESP coding | |
| MAZDA | ESP Module Replacement & Coding Errors | – Coding ESP, Parking system, and Active brake assist |
| MAZDA | – ESP VIN Mismatch Errors | |
| MAZDA | – ESP Data Transfer and Adaptation Issues | |
| MAZDA | – ESP Missing or Faulty Coding | |
| MAZDA | – ESP Functional Errors Related to ESP | |
| MAZDA | – ESP incorrect coding requires checking coding in EZS, collision data, and ESP | |
| MAZDA | – ESP incorrect coding error, vehicle history unknown | |
| MAZDA | – ESP error P1644FB: An incorrect variant coding or configuration detected | |
| MAZDA | – ESP coding errors: C1600, C1898, C1296 | |
| MAZDA | – Customer programmed ESP with Autel, resulting in programming and incorrect coding errors | |
| MAZDA | – Replaced ESP module with incorrect VIN and coding errors | |
| MAZDA | – Replaced ESP module (same part number), coding data from the old ESP caused C032300 error | |
| MAZDA | ESP Module Calibration & Adaptation | – Replacing ESP module with missing coding |
| MAZDA | – Replaced ESP control module, not coded, transferred data from the old ESP | |
| MAZDA | – Replaced ESP module, customer programmed VIN, resulting in variant coding error | |
| MAZDA | – Replaced ESP module with rear wheel lock error | |
| MAZDA | – SCN coding for ESP | |
| MAZDA | – ESP module calibration | |
| MAZDA | ABS & Related Issues | – Replacing ABS module error coding incorrect and calibration |
| MAZDA | – ESP error EBV ABS ESP inoperative on IC but no error in ESP | |
| MAZDA | – Replaced ABS module with incorrect part number causing VIN error | |
| MAZDA | AdBlue System Reset & Sensor Issues | – Turn off SCR AdBlue W222 |
| MAZDA | – Replacing AdBlue sensor causing “engine will not start after 103 km” | |
| MAZDA | – Resetting AdBlue system for limited remaining starts error | |
| MAZDA | – Reset AdBlue car cannot start for W906 CR43 | |
| MAZDA | – Reset AdBlue warning | |
| MAZDA | Radar & Active Brake Assist Calibration and Coding | – Replace ABA radar module coding and calibration errors |
| MAZDA | – Replace faulty radar sensor active brake assist functions limited | |
| MAZDA | – Replace front radar programming | |
| MAZDA | – Turn off radar sensor | |
| MAZDA | – Active brake assist errors | |
| MAZDA | – Replacing ADS coding | |
| MAZDA | – Replace A90 collision module programming and coding error | |
| MAZDA | Radar & Active Brake Assist Calibration and Coding | – Replace ABA radar module coding and calibration errors |
| MAZDA | – Replace faulty radar sensor active brake assist functions limited | |
| MAZDA | – Replace front radar programming | |
| MAZDA | – Turn off radar sensor | |
| MAZDA | – Active brake assist errors | |
| MAZDA | – Replacing ADS coding | |
| MAZDA | – Replace A90 collision module programming and coding error | |
| MAZDA | Radar Faults & Blind Spot Issues | – Right rear short-range radar incorrect coding error W206 |
| MAZDA | – CAN network car check + replace radar blind spot deactivated | |
| MAZDA | – Car accident remove rear bumper error: blind spot inoperative | |
| MAZDA | – Replace sensors, turn off collision warning | |
| MAZDA | Retrofit Options | – AMG menu activation (IC, HU) |
| MAZDA | – Ambient light (64-color) activation | |
| MAZDA | – Paddle shifter functionality | |
| MAZDA | Activation Features (AMG/Driving Modes) | – Activate AMG IC, A mode, M mode for VGS4 |
| MAZDA | – Activate A mode, M mode for EGS52 | |
| MAZDA | ECO Start/Stop Function | – Disabling ECO Start/Stop function (MED40 AMG engine) |
| MAZDA | – Activating ECO Start/Stop | |
| MAZDA | – Activating ECO ON-OFF reverse mode | |
| MAZDA | Speed Limit Removal & Unlocking | – Unlock Vmax speed Sprinter 906 |
| MAZDA | – Unlock speed limit for W907 CRD3S2NFZ | |
| MAZDA | – Unlock speed limit for W907 CR61NFZ | |
| MAZDA | – Unlock speed limit for W906 CR43 | |
| MAZDA | Door & Window Control System Issues | – Windows not working: need to reprogram driver door control box |
| MAZDA | – Retrofit folding mirror when locking the door | |
| MAZDA | – Programming door control box to fix glass lift error | |
| MAZDA | – Door control coding error after battery replacement | |
| MAZDA | Collision System & A90 Module Issues | – Replace start kit collision error A90 wrong VIN |
| MAZDA | – Replace A90 collision sensor coding error | |
| MAZDA | – Error A90 collision wrong VIN but actual value matches VIN | |
| GM | PSCM (Power Steering Control Module) | – Replace PSCM with incorrect VIN fault, requires programming. |
| GM | – Replace power steering with incorrect VIN fault and calibration. | |
| GM | BCM (Body Control Module) | – Replace BCM with immobilizer fault and programming. |
| GM | ABS and Parking Brake System | – Replace ABS and parking brake with incorrect VIN fault. |
| GM | ECU (Engine Control Unit) | – Replace ECU with immo VIN and as-built error, requires programming. |
| GM | ECM (Engine Control Module) | – Replace ECM with programming. |
| GM | Key Programming | – Programming to add new dealer key. |
| GM | Steering Gear (Steering Module) | – Replace steering gear with incorrect VIN fault, requires programming new module. |